This post which follows in relation to A Step-by-Step Guide to Installing a Bathtub is amazingly fascinating. Don't skip it.
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old tub is conveniently accessible, the project can move rapidly; if you need to open a wall to remove the old bathtub and position the brand-new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. Ensure you have certified yourself for the work and are comfortable trying it. Instead of hiring a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may require a professional plumber to make tube links.
This short article will certainly aid you set up a new bathtub in your shower room if you have actually currently acquired a brand-new tub as well as do not need to alter the plan of your previous water pipes.
Your devices as well as material checklist should make up the following:
- New Bath tub
- Hammer
- Pipeline Wrenches
- Prybar
- Shatterproof glass
- Level
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Blade
- Tape Measure
- Pipe Caps
Preparing for the Installation
Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain any type of water staying in the system. The process of getting rid of the existing faucets can be rather troublesome due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Utilizing both wooden boards under its feet, position the bathtub in the required setting. The wooden boards are handy in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the supply of water as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized at the very least when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washers are in area between the tap and also the sink. Protect the tap in position with the maker provided backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous kind must be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack a stiff seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealant can break rather early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were guided to that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on our other web page. Are you aware of somebody who is serious about the niche? Feel free to promote it. Thanks a lot for your time. Come back soon.
Quote & Schedule
